Manufactured in India, supplied in Dublin
PET felt acoustic panels in Dublin
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Dublin. Made at our own plant in India and shipped straight into Dublin Port, which sits inside the city, so the road leg to most sites is measured in minutes.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
Manufacturer, not reseller. We hold no local approvals and will not imply we do. You get the price the factory quotes, material that matches across a large order, and advice that sometimes talks you out of a purchase.
01 / The material
What this is, and what it changes in a Dublin room
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Dublin is mostly build-to-rent apartments, Georgian conversions, docklands offices, pubs and venues, clinics.
Terraced and semi-detached housing with block party walls and timber upper floors. Apartment stock is concrete with hard finishes throughout.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Dublin.
02 / Specification sheet
Published specification, identical wherever we ship it
Nothing below changes by location. The decisions that do change are grade, thickness and how the material is mounted, and those are covered further down.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
On a Dublin job with a consultant involved, our part is material that matches the submitted data. See working with acoustic consultants.
03 / In this market
What the buildings in Dublin do to the specification
- The port is in the city
Containers land at Dublin Port and are on site the same day. That is the practical reason a factory in India can compete here on landed cost and on timing.
- Build-to-rent party walls
Thousands of units built to the same separating detail. When that detail underperforms, it underperforms in every flat, so it is worth getting right on the drawing.
- Georgian conversions
High ceilings, lath and plaster, timber floors and protected fabric. Everything has to be done internally and shallow, and often reversibly.
- Late trading under homes
Pubs and venues now sit beneath apartments that were not there ten years ago. The low end and the footfall are what generate the complaints.
- School and campus buildings
School buildings run hard floors and lay-in ceilings with long corridors, and sports halls are the worst rooms in the building.
Architects working in Dublin usually need the build-up before the product. We will draw the section and mark what does the work. See how we support architects.
04 / Climate and durability
The Dublin climate decides the material list
Dublin is cool and damp, with long heating seasons and cold external walls, and that narrows the sensible material list before acoustics is even discussed.
Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would.
The risk we design against here is condensation behind linings in older, poorly insulated stock.
If the visual is fixed and the room still has to perform, that is a solvable problem and a conversation worth having early. See how we work with interior designers.
05 / Supply
How material reaches a Dublin site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Dublin Port, minutes from most city sites |
| Dispatch | 4 to 7 working days |
| Freight | Sea into Dublin Port |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Sea freight direct into Dublin Port, then a short road run to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Read this first
The things worth knowing before you place the order
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Square footage quoted before the room is understood
Anyone can price a wall. Working out how much material the room actually needs usually reduces the order, which is why not everyone does it.
-
Suppliers who imply a Dublin presence
Ask any supplier where the material is made and who carries the warranty. We make it at Palwal in Haryana and we say so on every page, including this one.
Dublin: questions we are actually asked
Are these PET felt acoustic panels made in Dublin?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Dublin as the manufacturer rather than through a dealer. Made at our own plant in India and shipped straight into Dublin Port, which sits inside the city, so the road leg to most sites is measured in minutes. You buy at factory prices with one consistent batch across the order.
Why would a Dublin build-up differ from anywhere else?
Containers land at Dublin Port and are on site the same day. That is the practical reason a factory in India can compete here on landed cost and on timing. Thousands of units built to the same separating detail. When that detail underperforms, it underperforms in every flat, so it is worth getting right on the drawing. Those two things move the build-up far more than the panel figure does.
Does Dublin weather shorten the life of this material?
Dublin is cool and damp, with long heating seasons and cold external walls. Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would. The failure we design against here is condensation behind linings in older, poorly insulated stock.
When would material land on a Dublin site?
ships from: Palwal, Haryana, India, arrives at: Dublin Port, minutes from most city sites, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Where do PET felt acoustic panels fail to help?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
Is there a minimum order, and how does it arrive?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Drawings in, BOQ and a delivered date out
One drawing gets you a proper answer. Build-up, quantities, a delivered date, and an honest note on anything we think is the wrong approach.