Manufactured in India, supplied in Seattle
PET felt acoustic panels in Seattle
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Seattle. Made at our own plant in India and shipped into Seattle or Tacoma, so the container lands at the city it is destined for rather than crossing the country first.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
Manufacturer, not reseller. We hold no local approvals and will not imply we do. You get the price the factory quotes, material that matches across a large order, and advice that sometimes talks you out of a purchase.
01 / What it is
The product, described honestly, for a Seattle brief
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Seattle is mostly mass timber offices, tech campuses, multifamily, studios, schools, clinics.
American homes are timber frame with gypsum board on both faces, so a party wall or a basement ceiling has almost no mass. Adding a second leaf with a limp membrane between does more than any amount of surface treatment.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Seattle.
02 / Specification
The numbers, and they do not move by city
We publish one data sheet for every market. If a supplier quotes you a different figure for the same product in a different city, one of the two numbers is wrong.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
On a Seattle job with a consultant involved, our part is material that matches the submitted data. See working with acoustic consultants.
03 / What drives the brief
The Seattle conditions that change the answer
- Mass timber is still light
Exposed timber looks solid and performs nothing like concrete at low frequency. It also cannot be covered, because the timber is the design, so the acoustic work has to happen where it will not be seen.
- Rain on the roof
Metal and membrane roofs over open volumes turn heavy rain into a noise source. It is worth designing for rather than discovering in the first storm.
- Campus open plans
Large tech floors with exposed structure and hard finishes carry speech a long way. The ceiling plane and screens have to do what the walls are not there to do.
- The port is right here
Containers land at Seattle or Tacoma, so there is no cross-country leg. That keeps the landed cost and the date both predictable.
- School and campus buildings
Public school buildings run long corridors with hard floors and lay-in tile ceilings that were chosen for cost, not for speech. Classroom reverberation and corridor spill are the two complaints, and both respond to ceiling area rather than wall panels.
For a Seattle practice, the useful thing is a detail you can put in a drawing set, not a brochure. See how we support architects.
04 / Durability
The Seattle climate decides the material list
Seattle is mild summers and cold, wet winters, and that narrows the sensible material list before acoustics is even discussed.
Cold external walls and long heating seasons make condensation behind a lining the thing to design out. PET felt is unaffected by damp air.
The risk we design against here is condensation and cold bridging behind new linings.
Interior designers tend to arrive with the look already decided. We will tell you which finish gets there without losing the acoustics. See how we work with interior designers.
05 / Supply
How material reaches a Seattle site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Seattle or Tacoma, then a short road run to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea into Seattle or Tacoma |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
Sea freight into Seattle or Tacoma, then a short road run to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Straight talk
What we will tell you that a reseller will not
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Coverage bought instead of a target
Lining every surface is a purchase, not a result. We would rather calculate the area against a reverberation target and sell you less of it.
-
Suppliers who imply a Seattle presence
Ask any supplier where the material is made and who carries the warranty. We make it at Palwal in Haryana and we say so on every page, including this one.
Seattle: questions we are actually asked
Are these PET felt acoustic panels made in Seattle?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Seattle as the manufacturer rather than through a dealer. Made at our own plant in India and shipped into Seattle or Tacoma, so the container lands at the city it is destined for rather than crossing the country first. You buy at factory prices with one consistent batch across the order.
Why would a Seattle build-up differ from anywhere else?
Exposed timber looks solid and performs nothing like concrete at low frequency. It also cannot be covered, because the timber is the design, so the acoustic work has to happen where it will not be seen. Metal and membrane roofs over open volumes turn heavy rain into a noise source. It is worth designing for rather than discovering in the first storm. Those two things move the build-up far more than the panel figure does.
How does the Seattle climate affect this product?
Seattle is mild summers and cold, wet winters. Cold external walls and long heating seasons make condensation behind a lining the thing to design out. PET felt is unaffected by damp air. The failure we design against here is condensation and cold bridging behind new linings.
When would material land on a Seattle site?
ships from: Palwal, Haryana, India, arrives at: Seattle or Tacoma, then a short road run to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
What should you not buy PET felt acoustic panels for?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What quantity do we have to order, and in what packaging?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Tell us the room, we will tell you the build-up
Send what you have. We will give you a layer by layer build-up, a bill of quantities and a date material lands, and we will flag anything in the brief that will not achieve what you want.