Manufactured in India, supplied in Cape Town
PET felt acoustic panels in Cape Town
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Cape Town. Made at our own plant in India and shipped straight into Cape Town, so the container lands at the city rather than crossing the country by road.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
This comes from our own plant, not a trading desk. We do not have an office in your city and we will not invent one. What we can give you is factory pricing, consistent material and a technical answer before you commit.
01 / What it is
The product, described honestly, for a Cape Town brief
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Cape Town is mostly hotels and restaurants, heritage conversions, offices, apartments, schools, studios.
Brick and concrete construction with hard floors. Townhouse and cluster developments share walls that were built for structure, not for separation.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Cape Town.
02 / Specification sheet
One specification sheet, the same in every market
Nothing below changes by location. The decisions that do change are grade, thickness and how the material is mounted, and those are covered further down.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
If a consultant has set the target, we will quote against their figures rather than ours, and stay out of the scope they own. More on working with acoustic consultants.
03 / Local conditions
The Cape Town conditions that change the answer
- Wind and coastal damp
PET felt does not absorb moisture or feed mould, which matters on exposed coastal elevations.
- The port is at the city
Direct sea into Cape Town avoids the long inland haul, which makes the landed cost and the date both easier to hold.
- Heritage fabric stays put
Older buildings in the city cannot be structurally altered. Work has to be internal, shallow and ideally reversible.
- Hospitality is the market
Hotels and restaurants where the room is part of what the guest is paying for, judged when it is completely full.
- School and campus buildings
Classrooms are hard walled with high ceilings and large class sizes, and school halls double as assembly and performance spaces.
For a Cape Town practice, the useful thing is a detail you can put in a drawing set, not a brochure. See how we support architects.
04 / Climate and durability
Durability in Cape Town, before acoustics is discussed
Cape Town is hot summers, mild winters and a distinct wet season, and that narrows the sensible material list before acoustics is even discussed.
PET felt handles the wet months without absorbing moisture or feeding mould. Timber and wood wool want a ventilated cavity and a stable indoor RH.
The risk we design against here is wet-season humidity behind linings.
Designers get colour, pattern and CNC options with the absorption figure attached to each. See how we work with interior designers.
05 / Route to site
Supply into Cape Town, start to site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Cape Town, then a short road run to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea into Cape Town |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Sea freight direct into Cape Town, then a short road run to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Worth knowing
Four honest warnings before you buy
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Square footage quoted before the room is understood
Anyone can price a wall. Working out how much material the room actually needs usually reduces the order, which is why not everyone does it.
-
A claim of being local to Cape Town
We manufacture in India and supply here. We do not run an office in this city and we will not pretend to, because you would find out on the first site visit.
Cape Town: questions we are actually asked
Where are the PET felt acoustic panels you supply to Cape Town actually made?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Cape Town as the manufacturer rather than through a dealer. Made at our own plant in India and shipped straight into Cape Town, so the container lands at the city rather than crossing the country by road. You buy at factory prices with one consistent batch across the order.
What changes the specification on a Cape Town job?
Direct sea into Cape Town avoids the long inland haul, which makes the landed cost and the date both easier to hold. Older buildings in the city cannot be structurally altered. Work has to be internal, shallow and ideally reversible. Those two things move the build-up far more than the panel figure does.
Is this the right material for Cape Town conditions?
Cape Town is hot summers, mild winters and a distinct wet season. PET felt handles the wet months without absorbing moisture or feeding mould. Timber and wood wool want a ventilated cavity and a stable indoor RH. The failure we design against here is wet-season humidity behind linings.
What is the delivery time into Cape Town?
ships from: Palwal, Haryana, India, arrives at: Cape Town, then a short road run to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
What should you not buy PET felt acoustic panels for?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What quantity do we have to order, and in what packaging?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Tell us the room, we will tell you the build-up
A plan and a section is enough. We will come back with a build-up, a BOQ and a delivered date, and we will say so if what you are asking for will not work.