Manufactured in India, supplied in Romania
PET felt acoustic panels in Romania
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Romania. Made at our own plant in India and shipped into Constanța, the largest port on the Black Sea, then road inland.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
We make this ourselves and ship it to you. No local branch, no borrowed certifications, no dealer margin. One batch across the whole order, and an honest answer when the product is wrong for the problem.
01 / Start here
The material, and what it actually does on a Romania job
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Romania is mostly automotive and manufacturing plants, offices and service centres, panel block housing, schools, hospitals.
Communist era panel blocks with concrete walls and no impact isolation, plus new concrete towers with hard finishes.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Romania.
02 / Specification sheet
One specification sheet, the same in every market
These figures are published and they do not move. The thing worth arguing about is not the number on the sheet, it is which grade and which build-up suits the room you are treating.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
If a consultant has set the target, we will quote against their figures rather than ours, and stay out of the scope they own. More on working with acoustic consultants.
03 / Local conditions
What the buildings in Romania do to the specification
- Constanța is a major port
Direct sailings and good onward road connections make this one of the easier routes into central Europe.
- Manufacturing plant noise
Presses, robots and compressors are low frequency and structure-borne. Enclosure at the source rather than absorption on a far wall.
- Panel block housing
Prefabricated concrete passes speech and footfall between flats through thin connected elements. Mass is the only reliable answer.
- Service centre floors
Large rooms full of people on calls, where privacy rather than echo is the real problem.
- School and campus buildings
School buildings are hard surfaced with long corridors and gymnasiums doubling as assembly halls.
Architects working in Romania usually need the build-up before the product. We will draw the section and mark what does the work. See how we support architects.
04 / Climate and durability
The Romania climate decides the material list
Romania is cold winters and warm summers, with a wide annual temperature range, and that narrows the sensible material list before acoustics is even discussed.
A wide annual swing stresses adhesive fixings and moves timber. Mechanical fixing beats adhesive alone, and PET felt is stable across the range.
The risk we design against here is adhesive failure and timber movement across the annual swing.
Interior designers tend to arrive with the look already decided. We will tell you which finish gets there without losing the acoustics. See how we work with interior designers.
05 / Route to site
How material reaches a Romania site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Constanța, then road inland |
| Dispatch | 4 to 7 working days |
| Freight | Sea via Constanța |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Sea freight into Constanța, then road inland. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Worth knowing
Four honest warnings before you buy
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
A number chased without a measurement
If nobody has measured the room or set a target, the specification is a guess with a decimal point in it. We will ask for the target before we quote the quantity.
-
A claim of being local to Romania
We manufacture in India and supply here. We do not run an office in this city and we will not pretend to, because you would find out on the first site visit.
Romania: questions we are actually asked
Is there a Romania factory behind this product?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Romania as the manufacturer rather than through a dealer. Made at our own plant in India and shipped into Constanța, the largest port on the Black Sea, then road inland. You buy at factory prices with one consistent batch across the order.
What decides the specification for a Romania project?
Direct sailings and good onward road connections make this one of the easier routes into central Europe. Presses, robots and compressors are low frequency and structure-borne. Enclosure at the source rather than absorption on a far wall. Those two things move the build-up far more than the panel figure does.
Is this the right material for Romania conditions?
Romania is cold winters and warm summers, with a wide annual temperature range. A wide annual swing stresses adhesive fixings and moves timber. Mechanical fixing beats adhesive alone, and PET felt is stable across the range. The failure we design against here is adhesive failure and timber movement across the annual swing.
How quickly can material reach a site in Romania?
ships from: Palwal, Haryana, India, arrives at: Constanța, then road inland, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
When are PET felt acoustic panels the wrong purchase?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What is the minimum order and how is it packed?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Tell us the room, we will tell you the build-up
We quote from drawings, not from a square foot rate. Send a plan and the section through the critical wall or ceiling and you will get something you can actually build from.