Manufactured in India, supplied in Japan
PET felt acoustic panels in Japan
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Japan. Made at our own plant in India and shipped into Yokohama or Kobe, then road to site, with the full window quoted rather than the port date.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
We are the manufacturer. There is no local office and we do not claim approvals we do not hold. What you get is factory pricing, one consistent batch across the order, and a straight answer on what the material will and will not do.
01 / Start here
The product, described honestly, for a Japan brief
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Japan is mostly apartments and houses, offices, studios, hotels, schools, clinics.
Timber frame houses and reinforced concrete mansions, with thin partitions in older stock and tight urban spacing throughout.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Japan.
02 / Specification
The published figures, unchanged by location
We publish one data sheet for every market. If a supplier quotes you a different figure for the same product in a different city, one of the two numbers is wrong.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
On a Japan job with a consultant involved, our part is material that matches the submitted data. See working with acoustic consultants.
03 / In this market
What the buildings in Japan do to the specification
- Humid summers
PET felt does not hold moisture or feed mould, which matters through a humid season in a sealed room.
- Small rooms, close neighbours
Depth is genuinely scarce, so a thin build-up that performs is worth more than a thicker one that performs marginally better.
- Designed to move
Seismic detailing means junctions that must stay flexible. An acoustic layer cannot bridge a movement joint rigidly.
- Precise expectations
Specifications here are written carefully and checked properly. Send us the target and we will say plainly what our material reaches.
- School and campus buildings
School buildings are hard surfaced with long corridors, and gymnasiums double as assembly halls.
If you are specifying for a Japan project, we can give you a section, a BOQ and the honest limits of each layer. See how we support architects.
04 / Durability
Why the climate in Japan changes the material, not the target
Japan is hot summers, mild winters and a distinct wet season, and that narrows the sensible material list before acoustics is even discussed.
PET felt handles the wet months without absorbing moisture or feeding mould. Timber and wood wool want a ventilated cavity and a stable indoor RH.
The risk we design against here is wet-season humidity behind linings.
Designers get colour, pattern and CNC options with the absorption figure attached to each. See how we work with interior designers.
05 / Getting it there
Supply into Japan, start to site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Yokohama or Kobe, then road to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea via Yokohama |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
Sea freight into Yokohama or Kobe, then road to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Straight talk
Four honest warnings before you buy
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
A number chased without a measurement
If nobody has measured the room or set a target, the specification is a guess with a decimal point in it. We will ask for the target before we quote the quantity.
-
Suppliers who imply a Japan presence
Ask any supplier where the material is made and who carries the warranty. We make it at Palwal in Haryana and we say so on every page, including this one.
Japan: questions we are actually asked
Do you manufacture PET felt acoustic panels in Japan?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Japan as the manufacturer rather than through a dealer. Made at our own plant in India and shipped into Yokohama or Kobe, then road to site, with the full window quoted rather than the port date. You buy at factory prices with one consistent batch across the order.
What do you look at first on a Japan enquiry?
Depth is genuinely scarce, so a thin build-up that performs is worth more than a thicker one that performs marginally better. Seismic detailing means junctions that must stay flexible. An acoustic layer cannot bridge a movement joint rigidly. Those two things move the build-up far more than the panel figure does.
Will this material last in the Japan climate?
Japan is hot summers, mild winters and a distinct wet season. PET felt handles the wet months without absorbing moisture or feeding mould. Timber and wood wool want a ventilated cavity and a stable indoor RH. The failure we design against here is wet-season humidity behind linings.
When would material land on a Japan site?
ships from: Palwal, Haryana, India, arrives at: Yokohama or Kobe, then road to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
Where do PET felt acoustic panels fail to help?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What is the minimum order and how is it packed?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Drawings in, BOQ and a delivered date out
Send what you have. We will give you a layer by layer build-up, a bill of quantities and a date material lands, and we will flag anything in the brief that will not achieve what you want.