Manufactured in India, supplied in Denmark
PET felt acoustic panels in Denmark
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Denmark. Made at our own plant in India and shipped into Aarhus or Copenhagen, then a short road run to almost anywhere in the country.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
Manufacturer, not reseller. We hold no local approvals and will not imply we do. You get the price the factory quotes, material that matches across a large order, and advice that sometimes talks you out of a purchase.
01 / The material
What this is, and what it changes in a Denmark room
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Denmark is mostly apartments, offices, schools, healthcare, timber buildings, studios.
Masonry blocks with timber joist floors in older stock and concrete in newer, with hard surfaces and cold external walls throughout.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Denmark.
02 / The numbers
One specification sheet, the same in every market
These figures are published and they do not move. The thing worth arguing about is not the number on the sheet, it is which grade and which build-up suits the room you are treating.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
Consultants get the raw data, not a sales sheet. That is the whole of our side of the job, and it is set out under working with acoustic consultants.
03 / On the ground
What we see driving Denmark briefs
- Classes are written and verified
Work here arrives with a target and gets checked afterwards. Send us the class and we will say plainly what our material reaches and where it does not.
- Design led interiors
Finish matters as much as performance. Colour consistency across a full order is part of the job, not an afterthought.
- Timber and lightweight construction
Light structures pass low frequency easily, so mass and decoupling do the work rather than more absorption.
- Sealed through a long winter
Buildings close up with ventilation running constantly, so plant noise matters more than street noise.
- School and campus buildings
Classroom acoustics are taken seriously, and open plan learning spaces make speech intelligibility the design target rather than echo.
If you are specifying for a Denmark project, we can give you a section, a BOQ and the honest limits of each layer. See how we support architects.
04 / Durability
What the Denmark climate rules in and rules out
Denmark is cool and damp, with long heating seasons and cold external walls, and that narrows the sensible material list before acoustics is even discussed.
Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would.
The risk we design against here is condensation behind linings in older, poorly insulated stock.
Designers get colour, pattern and CNC options with the absorption figure attached to each. See how we work with interior designers.
05 / Route to site
Supply into Denmark, start to site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Aarhus or Copenhagen, then a short road run to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea via Aarhus |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Sea freight into Aarhus or Copenhagen, then a short road run to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Straight talk
Four honest warnings before you buy
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Square footage quoted before the room is understood
Anyone can price a wall. Working out how much material the room actually needs usually reduces the order, which is why not everyone does it.
-
Suppliers who imply a Denmark presence
Ask any supplier where the material is made and who carries the warranty. We make it at Palwal in Haryana and we say so on every page, including this one.
Denmark: questions we are actually asked
Are these PET felt acoustic panels made in Denmark?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Denmark as the manufacturer rather than through a dealer. Made at our own plant in India and shipped into Aarhus or Copenhagen, then a short road run to almost anywhere in the country. You buy at factory prices with one consistent batch across the order.
What decides the specification for a Denmark project?
Work here arrives with a target and gets checked afterwards. Send us the class and we will say plainly what our material reaches and where it does not. Finish matters as much as performance. Colour consistency across a full order is part of the job, not an afterthought. Those two things move the build-up far more than the panel figure does.
Will this material last in the Denmark climate?
Denmark is cool and damp, with long heating seasons and cold external walls. Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would. The failure we design against here is condensation behind linings in older, poorly insulated stock.
How quickly can material reach a site in Denmark?
ships from: Palwal, Haryana, India, arrives at: Aarhus or Copenhagen, then a short road run to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
What should you not buy PET felt acoustic panels for?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
Is there a minimum order, and how does it arrive?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Send the drawings, get a straight answer
Send what you have. We will give you a layer by layer build-up, a bill of quantities and a date material lands, and we will flag anything in the brief that will not achieve what you want.