Manufactured in India, supplied in Vancouver
SoundBlanket mass loaded vinyl in Vancouver
We manufacture soundBlanket mass loaded vinyl at our own plant at Palwal in Haryana, India, and supply them into Vancouver. Made at our own plant in India and shipped straight into Vancouver, so the container lands at the city rather than railing across the country.
- Density
- 2100 kg per cubic metre
- 2.5 mm
- STC 30, 5.25 kg per sq m
- 4 mm
- STC 34, 8.4 kg per sq m
- 6 mm
- 12.6 kg per sq m, STC on request
- Roll size
- 5 x 1.2 m, 6 sq m per roll
- Lead time
- 4 to 7 working days
- Minimum order
- From 10 rolls
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
- Test reports sent on request, not just quoted
We are the manufacturer. There is no local office and we do not claim approvals we do not hold. What you get is factory pricing, one consistent batch across the order, and a straight answer on what the material will and will not do.
01 / The material
What this is, and what it changes in a Vancouver room
A limp, high density sheet that adds mass to a partition, floor or duct without adding depth. It is the barrier product, not an absorber, and it is the right answer when the problem is noise passing through a structure.
Work reaching us from Vancouver is mostly mass timber and light frame housing, condominium towers, offices, schools, studios, clinics.
Timber frame with gypsum board in low rise, concrete in towers. Condominium party walls and floors generate most complaints, and impact noise through a concrete slab needs a resilient layer, not a panel.
- Wall, decoupled Independent stud, membrane between the boards, cavity absorption, two boards. The membrane is one part of a system, never the whole answer.
- Floor, floating Membrane under a resilient layer and a floating deck, so impact energy is broken before it reaches the slab.
- Duct and plant wrap Membrane wrapped over the duct with a decoupling layer beneath, sealed at every lap.
- What it will not do Mass fixed hard to an existing wall gives far less than the same mass on an independent leaf. If we are told the wall cannot be thickened, we will say what the membrane will and will not achieve rather than quote the laboratory figure and let the site find out.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for SoundBlanket MLV are on the main product page. This page covers what that means for a project in Vancouver.
02 / Data sheet
The published figures, unchanged by location
These figures are published and they do not move. The thing worth arguing about is not the number on the sheet, it is which grade and which build-up suits the room you are treating.
- 2.5 mmSTC 30, 5.25 kg per sq m. Ducts, light partitions, retrofit where depth is tight
- 4 mmSTC 34, 8.4 kg per sq m. Party walls, floors, plant rooms, the common specification
- 6 mm12.6 kg per sq m. Machine enclosures and low frequency problems
| Density | 2100 kg per cubic metre |
|---|---|
| 2.5 mm | STC 30, 5.25 kg per sq m |
| 4 mm | STC 34, 8.4 kg per sq m |
| 6 mm | 12.6 kg per sq m, STC on request |
| Roll size | 5 x 1.2 m, 6 sq m per roll |
| Form | Limp sheet, cuts with a knife, seams lapped and sealed |
Consultants get the raw data, not a sales sheet. That is the whole of our side of the job, and it is set out under working with acoustic consultants.
03 / On the ground
What we see driving Vancouver briefs
- Timber is light
Mass timber looks solid and performs nothing like concrete at low frequency. Added mass and a decoupled layer do the work, not more absorption.
- Damp, mild climate
PET felt does not absorb moisture, shed fibre or feed mould, which suits cold external walls and sealed rooms.
- The port is right here
Direct sea into Vancouver means no rail leg across the country, so the landed cost and the date are both easier to hold.
- Rain on the roof
Metal and membrane roofs over open volumes turn heavy rain into a noise source worth designing for rather than discovering.
- The housing stock
Timber frame with gypsum board in low rise, concrete in towers. Condominium party walls and floors generate most complaints, and impact noise through a concrete slab needs a resilient layer, not a panel.
- The studio and content scene
Basement and garage studios are common, and a finished basement ceiling with no decoupling passes everything to the floor above.
We would rather argue about the build-up at design stage than on site. See how we support architects.
04 / Climate
Why the climate in Vancouver changes the material, not the target
Vancouver is cool and damp, with long heating seasons and cold external walls, and that narrows the sensible material list before acoustics is even discussed.
Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would.
The risk we design against here is condensation behind linings in older, poorly insulated stock.
Interior designers tend to arrive with the look already decided. We will tell you which finish gets there without losing the acoustics. See how we work with interior designers.
05 / Getting it there
Supply into Vancouver, start to site
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Vancouver, then a short road run to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea into Vancouver |
| Packing | Rolls on core tubes, wrapped and end capped, 5 x 1.2 m. Weights on the packing list, because a full roll is heavy and site access matters. |
| Lead time | 4 to 7 working days. Full container quantities scheduled against the vessel. |
Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
Sea freight direct into Vancouver, then a short road run to site. Air freight for samples and urgent quantities.
The same minimums apply on export as on domestic orders.
| 2.5 mm and 4 mm | 10 rolls, 60 sq m |
|---|---|
| 6 mm and other thicknesses | 10 tonnes per thickness |
A SoundBlanket roll is 5 x 1.2 m, which is 6 sq m. At 2100 kg per cubic metre a roll weighs about 31.5 kg at 2.5 mm and about 50.4 kg at 4 mm, so a 10 roll minimum is 60 sq m and roughly 315 kg at 2.5 mm or 504 kg at 4 mm.
06 / Worth knowing
Where this goes wrong, said plainly
-
The wrong product for the problem
Mass fixed hard to an existing wall gives far less than the same mass on an independent leaf. If we are told the wall cannot be thickened, we will say what the membrane will and will not achieve rather than quote the laboratory figure and let the site find out.
-
Coverage bought instead of a target
Lining every surface is a purchase, not a result. We would rather calculate the area against a reverberation target and sell you less of it.
-
A claim of being local to Vancouver
We manufacture in India and supply here. We do not run an office in this city and we will not pretend to, because you would find out on the first site visit.
Vancouver: questions we are actually asked
Are these soundBlanket mass loaded vinyl made in Vancouver?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Vancouver as the manufacturer rather than through a dealer. Made at our own plant in India and shipped straight into Vancouver, so the container lands at the city rather than railing across the country. You buy at factory prices with one consistent batch across the order.
Why would a Vancouver build-up differ from anywhere else?
Mass timber looks solid and performs nothing like concrete at low frequency. Added mass and a decoupled layer do the work, not more absorption. Metal and membrane roofs over open volumes turn heavy rain into a noise source worth designing for rather than discovering. Those two things move the build-up far more than the panel figure does.
Will this material last in the Vancouver climate?
Vancouver is cool and damp, with long heating seasons and cold external walls. Cold wall build-ups and long heating seasons mean interstitial condensation is a real risk behind any lining. PET felt is unaffected by damp air and will not feed mould where a fabric-faced mineral product would. The failure we design against here is condensation behind linings in older, poorly insulated stock.
How does an order actually travel to Vancouver?
ships from: Palwal, Haryana, India, arrives at: Vancouver, then a short road run to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. The sea leg from India is long, so plan the full door to door window into the programme. We give real dates, not optimistic ones.
What will soundBlanket mass loaded vinyl not do?
Mass fixed hard to an existing wall gives far less than the same mass on an independent leaf. If we are told the wall cannot be thickened, we will say what the membrane will and will not achieve rather than quote the laboratory figure and let the site find out.
What is the minimum order and how is it packed?
The same minimums apply on export as on domestic orders. 2.5 mm and 4 mm, 10 rolls, 60 sq m. 6 mm and other thicknesses, 10 tonnes per thickness. A SoundBlanket roll is 5 x 1.2 m, which is 6 sq m. At 2100 kg per cubic metre a roll weighs about 31.5 kg at 2.5 mm and about 50.4 kg at 4 mm, so a 10 roll minimum is 60 sq m and roughly 315 kg at 2.5 mm or 504 kg at 4 mm. Rolls on core tubes, wrapped and end capped, 5 x 1.2 m. Weights on the packing list, because a full roll is heavy and site access matters.
Next step
Drawings in, BOQ and a delivered date out
We quote from drawings, not from a square foot rate. Send a plan and the section through the critical wall or ceiling and you will get something you can actually build from.