Manufactured in India, supplied in Qatar
PET felt acoustic panels in Qatar
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Qatar. Made at our own plant in India and shipped into Hamad Port, a short run from western India, then a short road leg to almost anywhere in the country.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
Manufacturer, not reseller. We hold no local approvals and will not imply we do. You get the price the factory quotes, material that matches across a large order, and advice that sometimes talks you out of a purchase.
01 / The material
What this material is and where it earns its place in Qatar
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Qatar is mostly venues and event spaces, hotels, towers and apartments, offices, hospitals, schools.
Towers and compound villas in concrete and block with stone floors. Rooms are live and impact noise passes straight through the slab.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Qatar.
02 / Specification sheet
Published specification, identical wherever we ship it
Nothing below changes by location. The decisions that do change are grade, thickness and how the material is mounted, and those are covered further down.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
If a consultant has set the target, we will quote against their figures rather than ours, and stay out of the scope they own. More on working with acoustic consultants.
03 / In this market
What the buildings in Qatar do to the specification
- Sealed against extreme heat
Buildings stay closed with heavy cooling all year. Mechanical noise accumulates and rooms stay live.
- A short sea leg and a short road leg
Hamad Port is close to India by sea and close to everywhere by road, which makes the landed cost unusually predictable.
- Venues and assembly at scale
Large event and assembly spaces where amplified sound and intelligible speech both have to work in the same room.
- New concrete construction
The structure carries mass, so the recurring problem is reverberation inside and impact through slabs rather than airborne transfer.
- School and campus buildings
International school and university campuses are new, glazed and built fast, with atria and sports halls the problem rooms.
We would rather argue about the build-up at design stage than on site. See how we support architects.
04 / Climate and durability
What the Qatar climate rules in and rules out
Qatar is hot and dry for most of the year, with dust and high daytime surface temperatures, and that narrows the sensible material list before acoustics is even discussed.
Dust is the enemy of open-cell products. PET felt does not shed, does not hold dust in the way fabric-wrapped glass wool does, and wipes down. Timber needs a stable indoor RH or it moves.
The risk we design against here is dust ingress and thermal movement in long runs.
Designers get colour, pattern and CNC options with the absorption figure attached to each. See how we work with interior designers.
05 / Getting it there
What the route into Qatar actually looks like
| Ships from | Palwal, Haryana, India |
|---|---|
| Arrives at | Hamad Port, then a short road run to site |
| Dispatch | 4 to 7 working days |
| Freight | Sea via Hamad Port |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
Sea freight into Hamad Port, then a short road run to site. Air freight for samples and urgent quantities.
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use.
| Trial order | 200 panels, 6,400 sq ft, mixed thickness, GSM and colour |
|---|---|
| Recommended | Full container, for the best price per panel and the lowest freight per panel |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Worth knowing
The things worth knowing before you place the order
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Square footage quoted before the room is understood
Anyone can price a wall. Working out how much material the room actually needs usually reduces the order, which is why not everyone does it.
-
Suppliers who imply a Qatar presence
Ask any supplier where the material is made and who carries the warranty. We make it at Palwal in Haryana and we say so on every page, including this one.
Qatar: questions we are actually asked
Do you manufacture PET felt acoustic panels in Qatar?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Qatar as the manufacturer rather than through a dealer. Made at our own plant in India and shipped into Hamad Port, a short run from western India, then a short road leg to almost anywhere in the country. You buy at factory prices with one consistent batch across the order.
What changes the specification on a Qatar job?
Hamad Port is close to India by sea and close to everywhere by road, which makes the landed cost unusually predictable. Large event and assembly spaces where amplified sound and intelligible speech both have to work in the same room. Those two things move the build-up far more than the panel figure does.
How does the Qatar climate affect this product?
Qatar is hot and dry for most of the year, with dust and high daytime surface temperatures. Dust is the enemy of open-cell products. PET felt does not shed, does not hold dust in the way fabric-wrapped glass wool does, and wipes down. Timber needs a stable indoor RH or it moves. The failure we design against here is dust ingress and thermal movement in long runs.
When would material land on a Qatar site?
ships from: Palwal, Haryana, India, arrives at: Hamad Port, then a short road run to site, dispatch: 4 to 7 working days. Standard items dispatch in 4 to 7 working days. Grooved panels and custom colours take longer, and we say so before you order, not after.
When are PET felt acoustic panels the wrong purchase?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What quantity do we have to order, and in what packaging?
200 panels for a trial order, in any mix of thickness, GSM and colour. Beyond a trial we would rather quote a container load, because the price per panel and the freight per panel both fall sharply and a part load pays for space it does not use. Trial order, 200 panels, 6,400 sq ft, mixed thickness, GSM and colour. Recommended, Full container, for the best price per panel and the lowest freight per panel. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Send the drawings, get a straight answer
One drawing gets you a proper answer. Build-up, quantities, a delivered date, and an honest note on anything we think is the wrong approach.