Manufactured in India, supplied in Nagpur
PET felt acoustic panels in Nagpur
We manufacture PET felt acoustic panels at our own plant at Palwal in Haryana, India, and supply them into Nagpur. Nagpur sits at the centre of the country, which makes it a logistics hub and gives us an unusually even mix of industrial and institutional work.
- Material
- 100% PET non-woven, no added binder
- Thickness
- 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent
- Custom thickness
- 4 to 24 mm
- Panel size
- 1220 x 2440 mm standard, 4 x 8 ft
- Maximum size
- 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft
- Lead time
- 4 to 7 working days for standard colours and thicknesses
- Minimum order
- From 10 panels
- ASTM C423
- Made at our own plant, Palwal, Haryana, India
- One batch across the order, no blending between runs
We are the manufacturer. There is no local office and we do not claim approvals we do not hold. What you get is factory pricing, one consistent batch across the order, and a straight answer on what the material will and will not do.
01 / Start here
The material, and what it actually does on a Nagpur job
A rigid non-woven panel pressed from 100% polyester fibre, a large part of it recycled. It absorbs mid and high frequency energy and finishes as the visible surface, so it is both the acoustic layer and the finish.
Work reaching us from Nagpur is mostly warehouses and processing units, colleges, hospitals, offices, auditoriums, hotels.
Towers and chawls side by side, in RC frame with tile floors. Redevelopment stock shares slabs and lift cores, and monsoon damp rules out anything that holds moisture.
- Direct to wall Panel bonded or mechanically fixed flat to the substrate. Simplest, and the weakest at low frequency.
- On a 25 to 50 mm air gap The same panel on battens. The air gap moves absorption down in frequency at no extra material cost, and is the cheapest improvement available.
- Over a porous backing Panel over mineral or PET backing where the room needs genuine low mid control.
- What it will not do It absorbs. It does not block.
Full specification
Thickness, density, NRC by frequency, fire class, standard sizes and build-up detail for PET felt panels are on the main product page. This page covers what that means for a project in Nagpur.
02 / Specification
The published figures, unchanged by location
The specification below is the same everywhere we supply, because a specification that changed by city would not be a specification. What changes is which grade and build-up is the right buy, and that is what the rest of this page is about.
- EchoCore 151500 GSM. Offices, classrooms, general commercial
- EchoPro 181800 GSM. Studios, auditoria, rooms with a written RT target
- EchoMax 222200 GSM. High occupancy and high level spaces
| Material | 100% PET non-woven, no added binder |
|---|---|
| Thickness | 9, 12, 18 and 24 mm standard, tolerance plus or minus 5 percent |
| Custom thickness | 4 to 24 mm |
| Panel size | 1220 x 2440 mm standard, 4 x 8 ft |
| Maximum size | 2440 x 4270 mm, 2.44 x 4.27 m, 8 x 14 ft |
| Density range | 1200 to 3600 GSM |
| NRC | 0.30 at 9 mm, rising with thickness and air gap |
| Test standard | ASTM C423 |
Consultants get the raw data, not a sales sheet. That is the whole of our side of the job, and it is set out under working with acoustic consultants.
03 / In this market
What we see driving Nagpur briefs
- Dry heat
PET felt does not sag, shed fibre or degrade at high temperature, which matters in roof voids and rooms that get genuinely hot.
- Warehouse volumes
Very large steel and concrete sheds where alarms and instructions have to be understood. Targeted absorption fixes intelligibility without touching the machines.
- Processing machinery
Continuous plant noise close to occupied areas. Enclosure at the source is the reliable answer.
- Institutional buildings
Colleges and hospitals in concrete and tile, where lecture rooms defeat the speaker and consult rooms offer no privacy.
- School and campus buildings
Schools range from compact municipal buildings to large private campuses, all hard surfaced, with assembly halls doing duty as performance spaces.
If you are specifying for a Nagpur project, we can give you a section, a BOQ and the honest limits of each layer. See how we support architects.
04 / Durability
What the Nagpur climate rules in and rules out
Nagpur is warm and humid through most of the year, with a long wet season, and that narrows the sensible material list before acoustics is even discussed.
Humidity is the deciding factor. PET felt does not absorb moisture, shed fibre or feed mould, which is why it outlasts fabric-wrapped mineral wool in this climate. Wood wool and timber need a ventilated cavity behind them.
The risk we design against here is mould, sagging fabric finishes and swelling in timber.
Designers get colour, pattern and CNC options with the absorption figure attached to each. See how we work with interior designers.
05 / Route to site
Supply into Nagpur, start to site
| Made at | Our own plant, Palwal, Haryana |
|---|---|
| Reaches site in | two to three days |
| Dispatch | 2 to 4 working days |
| To site | two to three days |
| Packing | Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote. |
| Lead time | 4 to 7 working days for standard colours and thicknesses. Grooved and custom colours take longer, and we say so before you order. |
Standard items dispatch in 2 to 4 working days from our plant at Palwal. Grooved panels and custom colours take longer, and we say so before you order, not after.
By road from Palwal, roughly eleven hundred kilometres, normally two to three days on a dedicated truck.
From 10 panels for 9 mm EchoCore 15. Other grades and thicknesses carry their own minimum.
| 9 mm EchoCore 15, 1500 GSM | 10 panels, 320 sq ft |
|---|---|
| 9 mm EchoPro 18, 1800 GSM | 50 panels, 1,600 sq ft |
| 9 mm EchoMax 22, 2200 GSM | 100 panels, 3,200 sq ft |
| 12 mm, 2400 GSM | 30 panels, 960 sq ft |
| 18 mm, 3000 GSM | 50 panels, 1,600 sq ft |
| 24 mm, 3600 GSM | 50 panels, 1,600 sq ft |
A panel is 1220 x 2440 mm, which is 32 sq ft.
06 / Before you buy
Four honest warnings before you buy
-
The wrong product for the problem
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
-
Coverage bought instead of a target
Lining every surface is a purchase, not a result. We would rather calculate the area against a reverberation target and sell you less of it.
-
A claim of being local to Nagpur
We manufacture in India and supply here. We do not run an office in this city and we will not pretend to, because you would find out on the first site visit.
Nagpur: questions we are actually asked
Is there a Nagpur factory behind this product?
No, and we will not say otherwise. We manufacture at our own plant at Palwal in Haryana, India, and supply into Nagpur as the manufacturer rather than through a dealer. Nagpur sits at the centre of the country, which makes it a logistics hub and gives us an unusually even mix of industrial and institutional work. You buy at factory prices with one consistent batch across the order.
What decides the specification for a Nagpur project?
Very large steel and concrete sheds where alarms and instructions have to be understood. Targeted absorption fixes intelligibility without touching the machines. Continuous plant noise close to occupied areas. Enclosure at the source is the reliable answer. Those two things move the build-up far more than the panel figure does.
How does the Nagpur climate affect this product?
Nagpur is warm and humid through most of the year, with a long wet season. Humidity is the deciding factor. PET felt does not absorb moisture, shed fibre or feed mould, which is why it outlasts fabric-wrapped mineral wool in this climate. Wood wool and timber need a ventilated cavity behind them. The failure we design against here is mould, sagging fabric finishes and swelling in timber.
What is the delivery time into Nagpur?
made at: Our own plant, Palwal, Haryana, reaches site in: two to three days, dispatch: 2 to 4 working days. Standard items dispatch in 2 to 4 working days from our plant at Palwal. Grooved panels and custom colours take longer, and we say so before you order, not after.
When are PET felt acoustic panels the wrong purchase?
It absorbs. It does not block. A PET panel on a shared wall will make the room sound better and will not stop the neighbour being heard. If the brief is stopping noise passing through a wall or floor, the answer is mass and decoupling, and we will say so before quoting.
What quantity do we have to order, and in what packaging?
From 10 panels for 9 mm EchoCore 15. Other grades and thicknesses carry their own minimum. 9 mm EchoCore 15, 1500 GSM, 10 panels, 320 sq ft. 9 mm EchoPro 18, 1800 GSM, 50 panels, 1,600 sq ft. 9 mm EchoMax 22, 2200 GSM, 100 panels, 3,200 sq ft. 12 mm, 2400 GSM, 30 panels, 960 sq ft. 18 mm, 3000 GSM, 50 panels, 1,600 sq ft. 24 mm, 3600 GSM, 50 panels, 1,600 sq ft. A panel is 1220 x 2440 mm, which is 32 sq ft. Palletised flat and film wrapped, cut sheets interleaved. Packing list and weights issued with the quote.
Next step
Tell us the room, we will tell you the build-up
We quote from drawings, not from a square foot rate. Send a plan and the section through the critical wall or ceiling and you will get something you can actually build from.